XT-4: 4-Channel Stationary Mid-range Transmitter

The Nortek Security & Control Family of Brands

This product is discontinued

The Model XT-4 4-Channel Stationary Mid-range Transmitter is designed for use in various wireless remote control applications. When triggered with an external switch, the Model XT-4 transmitter will send a 10 watt, 27.255 MHz, digital encoded, FSK modulated, signal to its companion receiver. The receiver will verify the digital code, activate its output, and trigger the remote device.

The XT-4 transmitter has full supervision capabilities. If the status option is selected, the XT-4 sends hourly status signals to its receiver. If these signals cease, the receiver will indicate trouble by activating its status output after four hours. Contact supervision allows the receiver’s outputs to follow the transmitter’s inputs, staying activated as long as each transmitter input is activated. Alternately, an auto-restore option can be selected, causing a momentary receiver output each time any transmitter input is activated. Each input can be configured for either N/O or N/C contacts (switch selectable).

Power for the XT-4 transmitter can come from an external regulated 12 VDC power supply (Linear Model T-1224DC) or from a 12-volt battery. A 3-amp fuse protects the unit from reverse power polarity. The XT-4 draws about 15 µA standby, and about two amps during transmissions. If the power supply voltage drops below 10.5 volts, a low battery message will be included with any signal transmitted, causing the receiver’s low battery output to activate.

Two antennas (sold separately) are available for the XT-4. The Model ANT-1A is an 7-inch rubber duck antenna for short range applications (less than 1 mile). The ANT-1A is supplied with a CON-180A (straight) connector to mate the antenna to the transmitter. For a right angle antenna mounting, use a CON-90A right-angle connector with the CON-180A. The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from the XT-4 is required. A common 9-foot 1/4 wave CB whip antenna can also be used with the XT-4 for maximum range.

Two 8-position switches set the unit’s system code. This code must be matched in the XT-4’s receiver. There are 65,536 different system codes possible. The 4-position option switch selects the receiver’s bank (for XR-16 receiver only), and options for status and auto-restore transmissions.

The transmitter is housed in a rugged weather-resistant metal enclosure with a sturdy SO-239 antenna connector and a water-tight wiring strain relief bushing. During transmissions, the red operation indicator (visible through a window on the case) lights. If the XT-4’s input voltage is low, the indicator will blink during transmissions.

Features

  • Up to 10 miles of line-of-sight range
  • RF transmit LED
  • Accepts four N/O or N/C inputs
  • Complete RF supervision, field enabled
  • Fully supervised (loop status, low battery, link integrity)
  • Weather-Resistant Case
  • Antenna (ANT-1A or ANT-2) not included
  • Power: 12 VDC
  • Codes: Over 64,000
  • RF frequency: 27.255 MHz
  • Dimensions: 4.25″ W x 6.25″ H x 2.5″ D

Order number: SST00084

XT-4
Operating Temperature: -4° to +140° F (-20° to +60° C)
Operating Frequency: 27.255 MHz
Bandwidth: 6 KHz
Number of Codes: 65,536
Code Setting Method: DIP switch programming
Operating Voltage: 12 to 15 VDC (power source not supplied)
Operating Current: Standby – 15 µA, transmitting -2.0 Amps at 12 VDC
Weight: 1.0 lbs. (0.454 Kg)
Housing: black, weather-resistant, anodized aluminum enclosure with removable end caps to provide wiring and programming access; end caps secured with screws
RF Output Power: 10 Watts typical
Loop Response Time: 500 msec
Code Transmissions: Alarm, restore, status, and low battery
Status Report Time Frame: 70 minutes
Transmit Time: 1 second
Antenna Impedance: 50 Ohms (antenna not supplied; see ANT-1, ANT-2)
Dimensions: 4.25″ W x 6.25″ H x 2.5″ D (108 x 159 x 64 mm)

Installation Manual
Literature

Dealer Login

JOIN US IN 2017

Nortek Security & Control is presenting at a number of trade shows this year. Please join us at a show near you!

READ MORE

NEW FEATURE DEVELOPED

Please visit our Dealer Locator to verify your contact information is accurate. We're constantly making updates to serve you and your customers.

READ MORE

Product Search

Subscribe to Our Newsletter